Dog3 / Doge V3 Copper Center Post Safe?

Apparently not many people have mentioned if the copper center post was safe enough to vape. I did some research that people said that copper can be dangerous when heated over 1000 degrees F. Congrevape has said that the copper center posts are lead free.

Should I vape with copper center posts? I am going to use SS 316L build around 0.22-0.25 ohms using both TC mode and wattage. I'll be vaping around 60 watts.

Thanks! :D

First RDA, need coil advice

Hi, I've just got my 1st RDA, a Hadaly by Psyclone… Bottom feeding it through my 1st mech <a href="https://vaping.com/vapemods?utm_source=ECF&utm_medium=Wordlink&utm_campaign=modS%20-%20Wordlink&utm_term=modS%20-%20Wordlink&utm_content=SMOK%20-%20Wordlink” rel=”nofollow” target=”_blank”>mod (Mölly by L'Atelier)

I usually build my coils at around 1ohm and vape at 21watts (rta)

I was thinking with this setup I'd like to build my coil around 0.5 – 0.6 ohm

I was building my coil with my 26ga Kanthal and realised for an 0.6ohm I would only give it 4 wraps with a 3mm diameter… That felt too few wraps so I gave it 6 and ended up with a 0.95ohm which I'm vaping on as I write this, I…

First RDA, need coil advice

Warm Rda

Hello guys… I recently bought an rda the "Druga" on my local shop and they made dual clapton coils for it and it was working beautifully. Today I ordered a kit from amazon of pre made coils and I installed a set of fused clapton that were supposed to be .25 but the mod is reading .139. I have a smok alien and the reads are the following vaping at 50w.

V 2.74
Ohm .139
Amps 19.70

The rda is getting really hot with this coils and the top of the mod as well… I took the batterys out after…

Warm Rda

Even glows

Hello. I have been building my own coils for some time now and recently started with claptons but my problem is that for some reason i cant get them to glow from the middle and out. The only way they glow is the whole coil lighting up at once ihave tried pinching and strumming but without results im currently building on a ijoy combo rda with dual coils on a ipv x6 mod

Smok Baby Beast on low wattage reviews

So I got to test out my buddies baby beast the other day on 6mg <a href="https://vaping.com/eliquid?utm_source=ECF&utm_medium=Wordlink&utm_term=Eliquid&utm_campaign=Wordlink%20-%20Eliquid” rel=”nofollow” target=”_blank”>liquid and I loved the hit. I haven't been vaping to long but started with Aspire Nautilus 2. MTL for a week on 1.8 coils. Started DL on their sub ohm coils but the Nautilus 2 just isn't setup for it. I need to lung hit to be happy. My <a href="https://vaping.com/vapemods?utm_source=ECF&utm_medium=Wordlink&utm_campaign=modS%20-%20Wordlink&utm_term=modS%20-%20Wordlink&utm_content=SMOK%20-%20Wordlink” rel=”nofollow” target=”_blank”>mod is 50 watts and has all adjustable options TC Ni, SS, temp, bypass, etc. At 21 watts I can get 4-5 days from the mod.

Is the baby beast a good daily driver option with the .6 ohm coils or…

Smok Baby Beast on low wattage reviews

Need a tank recommendation

Hey guys,

Been awhile since I've been here. Left awhile ago. I hope the <a href="https://vaping.com/vapemods?utm_source=ECF&utm_medium=Wordlink&utm_campaign=modS%20-%20Wordlink&utm_term=modS%20-%20Wordlink&utm_content=SMOK%20-%20Wordlink” rel=”nofollow” target=”_blank”>mods have improved.

I've been using a IPV D3 box mod with a Herakles version 1 tank. I've loved it to death but I do have 1 issue. It's tough to refill the tank and often times I spill <a href="https://vaping.com/eliquid?utm_source=ECF&utm_medium=Wordlink&utm_term=Eliquid&utm_campaign=Wordlink%20-%20Eliquid” rel=”nofollow” target=”_blank”>juice. I know there are updated versions of the Herakles tank and I just checked the sense website and they had a bunch of other tanks. Any recommendations for a tank that's regarded as top notch and similar to the herakles? Thanks!

40mm RDA or RTA

So I ordered the HOG V3 the other day and I'm looking for a 40mm RDA or RTA to put on it. I'm familiar with the Mason and the Dumptank which I have both in the 30mm version. I'm wondering what other 40mm pieces I can put on it. If you have a 40mm <a href="https://vaping.com/vapemods?utm_source=ECF&utm_medium=Wordlink&utm_campaign=modS%20-%20Wordlink&utm_term=modS%20-%20Wordlink&utm_content=SMOK%20-%20Wordlink” rel=”nofollow” target=”_blank”>device either RDA or RTA let me know what you have and why you picked it. Give me pros/cons on it. These things aren't cheap as you know and I don't want to get one and not like it or wish I would have went with another choice. Thanks!

Sent from…

40mm RDA or RTA

Coil leg direction?

I have an avocado 24 on a smok alien 220w <a href="https://vaping.com/vapemods?utm_source=ECF&utm_medium=Wordlink&utm_campaign=modS%20-%20Wordlink&utm_term=modS%20-%20Wordlink&utm_content=SMOK%20-%20Wordlink” rel=”nofollow” target=”_blank”>mod. I've been researching coil building and I came across a site talking about having certain RTAs that require coil legs pointing in the same or opposite direction.

For my tank and mod which do I have to have, both coil legs in the same direction or both legs in the opposite direction? Also by both coil legs, it means both legs on one coil not 2 coils, right?

Thanks for the help.